Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FLEX NORYL™ Resin WCD801A - Asia - (PPE+TPE) - Saudi Basic Industries Corporation (SABIC)

Check here, which other Flex Noryl datasheets, application examples or technical articles are available in Material Data Center

Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Recomendação de processamento Moldagem por injeção - Diagrama

Any use of this information falls under the rules of our disclaimer.

Informação do produto

FLEX NORYL™ WCD801A resin is a flexible, non-reinforced, migration improved, extrudable blend of Polyphenylene Ether (PPE) + Thermoplastic Elastomer (TPE). This material contains non-halogenated flame retardant and performance capable of meeting UL VW-1 requirements, 80C end use temperature rating, and heat deformation performance as defined by UL 1581. FLEX NORYL WCD801A resin is intended for evaluation in wire insulation and cable jacket applications in dark colors. It has a Shore A Hardness reading of 80 and exhibits superior thermal stability, very low water absorption, good electric properties, and low specific gravity. Processing is typically conducted on standard extrusion equipment, and UL 1581 testing is conducted on 2.0mm wire with 0.12mm X 20 stranded copper conductor.

UL Yellow Card Link E207780-536311

Características de processamento/físicas	Valor	Unidade	Método de ensaio
ISO Dados
Condutividade térmica do fundido	0.2	W/(m K)	-
Capacidade térmica específica do fundido	2050	J/(kg K)	-
Temperatura de ejeção	68	°C	-
ASTM Dados
Índice de fluidez, MFI	11	g/10min	ASTM D 1238
Temperatura	250	°C	-
Carga	5	kg	-

Propriedades mecânicas	Valor	Unidade	Método de ensaio
ISO Dados
Tensão na ruptura	13	MPa	ISO 527
Deformação na ruptura	50	%	ISO 527
ASTM Dados
Resistência à tração na ruptura	12	MPa	ASTM D 638
Deformação na ruptura	120	%	ASTM D 638
Dureza Shore A	80	-	ASTM D 2240

Propriedades térmicas	Valor	Unidade	Método de ensaio
ISO Dados
Coef. de expansão térmica linear, paralelo	87.4	E-6/K	ISO 11359-1/-2
Coef. de expansão térmica linear, perpend.	175	E-6/K	ISO 11359-1/-2
Flamabilidade a espessura h	V-0	class	IEC 60695-11-10
Espessuras do tubo de teste	4.0	mm	-
Glow Wire Ignition Temperature (GWIT)	750	°C	IEC 60695-2-13
GWIT - thickness tested (3)	3	mm	-

Propriedades elétricas	Valor	Unidade	Método de ensaio
ISO Dados
Constante dielétrica, 1MHz	2.8	-	IEC 62631-2-1
Fator de dissipação dielétrica, 1MHz	40	E-4	IEC 62631-2-1
Resistividade volumétrica específica	>1E13	Ohm*m	IEC 62631-3-1
Índice comparativo de linha de fuga	600	-	IEC 60112

Outras propriedades	Valor	Unidade	Método de ensaio
Densidade	1100	kg/m³	ASTM D 792

Recomendação de processamento Moldagem por injeção	Valor	Unidade	Método de ensaio
Velocidade de parafuso	15 - 85	rpm	-

Diagrama

Características

Aditivos

Anti-chama

Características especiais

Retardante de chama

Disponibilidade regional

Ásia Pacífico

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.